F Ball Stopgap SRS Surface Reinforcement System 10KG
Xtra Discount @ Basket
OR X
PAY OVER 3 MONTHS – 0% INTEREST
Estimated Delivery is 1-5 Days
Information About F Ball Stopgap SRS Surface Reinforcement System 10KG
F Ball Stopgap SRS Surface Reinforcement System 10KG is a solvent-free, low viscosity, two-component epoxy resin reinforcement material designed to quickly stabilise and reinforce poor and weak sand/cement or calcium sulphate screeds, including those containing hot water heating pipes. The product readily fills voids and cracks and binds loose particles resulting from poor installation and curing techniques of screeds.
STOPGAP SRS, in most applications, can negate the need to remove and replace poorly compacted or weak screeds which can be costly and time-consuming, especially if the subfloor contains underfloor heating, thereby minimising disruption in the construction programme.
The product may also be used over certain screeds containing high levels of construction moisture or where no effective damp proof membrane is present, prior to the application of STOPGAP F77 Waterproof Surface Membrane (Protocols for the use of STOPGAP F77 must be observed).
An assessment should be made of the screed in question to determine the likelihood of success, as these instructions are for guidance purposes only and may contain information that may be inappropriate for certain sites. Specific information and testing requirements are available upon request from the Technical Service Department.
COVERAGE
Coverage will be approximately 3kg/m2 dependent upon depth and porosity of the screed. Weaker, more porous screeds may require up to 5kg/m2.
Coverage rates are best determined by undertaking a small test area to evaluate the condition of the subfloor and help to calculate the quantity of material required.
- Pot life of mixed material in container @ 200C: 10 minutes
- Working time at 200C when applied to the subfloor: 30 minutes
- Setting time at 200C: 12 hours
- Drying time (ready to receive further treatments): 2-12 hours
- Application rate: 3-5kg/m²
- COVERAGE RANGE: 2 - 3.4m²
Product Information
The F Ball Stopgap SRS Surface Reinforcement System 10KG is a technologically advanced, solvent-free, low viscosity, epoxy resin reinforcement system that works to strengthen and maintain weak or poorly compacted sand-cement or calcium sulphate screeds. It is specifically designed to readily fill cracks and voids, binding loose particles left behind from sub-standard screed installation and curing processes. Notably, the Stopgap SRS can eliminate the need for costly and time-consuming screed removal and replacement, especially in the case of subfloors containing underfloor heating, hence reducing disruption in construction schedules.Moreover, the F Ball Stopgap SRS can be used over screeds containing high moisture levels or without an adequate damp proof membrane. However, it is crucial to apply a layer of STOPGAP F77 Waterproof Surface Membrane for optimal results, adhering to its usage protocols. An initial assessment of the screed is nonetheless essential to determining the potential for success with the product, given that guidelines may not be universally applicable to all construction sites. For specific information and additional testing requirements, responses from the Technical Service Department can be sought.
Coverage is expected to be around 3kg/m2, depending on the porosity and depth of the screed. However, weaker, more porous screeds may require an increased amount of up to 5kg/m2. Identifying the correct coverage level can best be achieved by conducting a small test area in order to evaluate the subfloor's condition and provide a more accurate calculation of the required material quantity. It is useful to note that, at 20°C, the pot life of the mixed material remains within the container for 10 minutes.
Application must be completed promptly as the working time once applied to the subfloor is only 30 minutes. The setting time at 20°C is roughly 12 hours and following this, the drying time before it is ready to take on further treatments is 21-12 hours. The application rate is given at 3-5kg/m² with the total coverage range of a 10KG bag being approximately 2-3.4m². This provides a cost-effective solution, reinforcing structural integrity without compromising on project timescales.
Further information related to F Ball Stopgap SRS Surface Reinforcement System 10KG
Check out the full range of F Ball available to buy online through Flooring HUT. We can also introduce you to a much more varied selection of Flooring Tools from other leading brands and manufacturers in the UK.
| Manufacturer | F Ball |
|---|---|
| Brand | F Ball |
| Range | F Ball Stopgap screeds & Adhesives |
| Business Delivery Only | No |
| No Of Delivery Days | 1-5 |
I bought marmoleum flooring on the roll. Quick delivery and excellent price per sq metre.
Great price, great product, speedy service.
-
F Ball Stopgap 1200 Pro Bag & Bottle 20kgUnit Price: £29.96Xtra Discount @ Basket
All prices are including VAT -
F Ball Stopgap 300 HD Heavy Duty Smoothing 25KgBag Price: £28.68Xtra Discount @ Basket
All prices are including VAT -
F Ball Stopgap P131 General Purpose PrimerUnit Price: £45.91Xtra Discount @ Basket
All prices are including VAT -
F Ball Styccobond F49 Adhesive 5KGUnit Price: £71.70Xtra Discount @ Basket
All prices are including VAT -
F Ball Styccobond F49 Adhesive 2KGUnit Price: £35.96Xtra Discount @ Basket
All prices are including VAT -
F Ball Pointed Nose Smooth TrowelUnit Price: £24.43Xtra Discount @ Basket
All prices are including VAT -
F Ball Adhesive Trowel V Notch A2 1.5mm x 3mmUnit Price: £22.19Xtra Discount @ Basket
All prices are including VAT -
F Ball Pressure Sensitive Styccobond F46 Adhesive 15LUnit Price: £111.71Xtra Discount @ Basket
All prices are including VAT -
F Ball Pressure Sensitive Styccobond F46 Adhesive 5LUnit Price: £39.74Xtra Discount @ Basket
All prices are including VAT
